I am Sara. I have an online service company. I usually put training on the company's website. These tutorials can help anyone to prevent clogged pipes and if this happens with the following methods can be removed with minimal cost.
We all know the warning signs for when a sewer pipe wants to be blocked. It takes time to drain the water in the sink, the water under your feet fills the bathroom, or you smell strange and nasty. All of these are signs that you will soon have a clogged sewer pipe. Before contacting the pipe opener company, it is better to try 10 immediate ways to remove the clogged sewer pipe.
First of all, it is better to know the various causes of clogged sewer pipes and wells so that you know why the sewer pipe gets clogged at once and how to solve the problem.
Various causes of clogged sewer pipes
• Long hair
• Sediment and mass
• Oil and fat
• Small objects fall into the pipe
• tissue paper
• Sanitary pad
Another reason for blocking sewer pipes is the pouring of construction materials such as cement, slurry, bitumen, etc., which you can not use the 10 methods described below to open such clogs. In fact, because the blockage is severe, the best way is to use the services of Tehran Pipe Opener.
10 Instant Ways to Open a Sewer Pipe
You may know the methods yourself or have heard what you can do when raising a sewer. But it is better to carefully study the methods described below to remove clogged sewer pipes to learn solutions that are fully tested and guaranteed, and you can use them to open most clogs.
1. Make a hook with a clothes hanger
Simple enough, but amazingly effective. Prepare a coat or clothes hanger and smooth out all the curves. Then bend the end or head to make it look like a hook. It is best to tie a piece of cloth to the hook to avoid damaging the pipe or toilet bowl. Now insert it into the drain pipe to remove the clogged sewer pipe. This is similar to fishing, and you have to pull out everything inside the tube, such as hair, sludge and objects. Be careful that you pull out these materials and do not push them in too far to move them forward. When you have removed enough material, pour hot water into the tube to clean everything.
2. Baking soda and vinegar
Mix one-third cup of baking soda with one-third cup of vinegar in one measuring cup. Immediately without wasting time, you should pour it into the sewer pipe. The combination of these two substances and creating a chemical reaction can help to open the clogged sewer pipe and remove hair, lime, fat, etc. It is better to wait an hour or even 12 hours after pouring the solution and then wash it with warm water. Another way is to pour the same amount of baking soda into the tube and then add vinegar to it. People often use this method more to eliminate the bad smell of sewage. Because this solution solves 90% of the problems.
3. Wet and dry vacuum cleaner
If you have a dry vacuum cleaner at home, it can be a great tool for opening pipes. First, set it to the wet section. Now insert the vacuum cleaner hose into the tube and cover it with plastic so that air does not enter and exit so that suction can be done with full force. Turn on the device and suck the tube blocking agent. With a wet and dry vacuum cleaner, you can open the clogged sewer pipe that has happened to hair, objects and grease without the need for pipe opening and draining services.
4. Boiling water
There is no easier way to clog a sewer pipe. Put a kettle on the gas to boil. Now, in two or three steps, slowly pour the boiling water into the tube and allow the boiling water to do its job for a few seconds in each step. This is usually the easiest and fastest way to open a pipe. If it does not work, you can repeat it again.
5. Burning profit
Be sure to use gloves and eye protection before using the fifth method. Caustic soda is also known as sodium hydroxide and can cause chemical burns if you are not careful when using it and do not follow safety tips. You can get this material from the store. To make the solution, you need to add 3 cups of baking soda to 3 gallons of cold water. Then stir it with a good stick until ready. Then pour gently into the sewer pipe in several steps. Wait 20 to 30 minutes and then pour in boiling water.
6. Manual spring tube opener
A great tool for unclogging a sewer pipe. This device has a long wire-like spring that has two different types of dry and flexible. You can get a 6-meter spring from the store. To open the pipe with a spring, place it in the sewer pipe and push it until it hits. Then turn it clockwise or counterclockwise to loosen the jam. Finally, pour hot water into the tube to wash everything.
7. Degreasing and descaling of pipes
Some pipe openers are easy to do and can be done at home. You must have seen the U-shaped pipes under the sink. Many times clogging occurs in that area, which will be solved by cleaning it. To begin unclogging a sewer pipe, first place a bucket under a U-shaped siphon and then open it. Thoroughly clean the tube with a brush and rinse thoroughly, then reinstall it.
8. Salt and baking soda
Combine a quarter cup of baking soda with the same amount of salt and pour into a tube. After 20 minutes, pour boiling water into it. The chemical reaction of these substances can open many clogs caused by hair, grease or sediment.
9. Dishwashing liquid
If you have a clogged toilet drain, pour half a cup of dishwashing liquid into the bowl. Then prepare some boiling water. Dishwashing liquid is a blocking agent that removes grease from everything. Now pour hot water into the toilet.
10. Vinegar, baking soda and air pressure
If you have a problem with clogged bathroom sewer pipe. Pour half a cup of vinegar and baking soda into the tube and put the lid on to keep air out. After 60 minutes, pour at least 5 buckets of water with pressure into the tube.
These 10 methods were the fastest and easiest methods to remove clogged sewer pipes. If you know the best ways to open the pipe, contact us through the comments section.
If you are looking for more tutorials, you can visit our websites and learn more: